Welcome to LDX official website!

Foshan Li Dexin Machinery Manufacturing Co., Ltd.
Foshan Li Dexin Machinery Manufacturing Co., Ltd.

 WeChat

Foshan Li Dexin Machinery Manufacturing Co., Ltd.

Foshan Li Dexin Machinery Manufacturing Co., Ltd.

Specializing in the production of TCT circular saw blades, TCT band saw blades, finger joint knives, flying knives, various non-standard CNC grinding machine production lines

Check category

The lightsaber technology of the rack of the band saw blade grinder

  • Time of issue:2020-06-30 10:26

(Summary description)The lightsaber technology of the rack of the band saw blade grinder

The lightsaber technology of the rack of the band saw blade grinder

(Summary description)The lightsaber technology of the rack of the band saw blade grinder

  • Time of issue:2020-06-30 10:26
The lightsaber technology of the rack of the band saw blade grinder
 
1. Technology
 
(1) Due to the particularity of the rack, the grinding wheel is generally wider, grinding multiple tooth grooves at a time. At this time, the grinding load is large, and the rigidity of the machine tool needs to be good enough, and the power of the spindle is large enough.
 
(2) The single-piece small rounded diamond wheel can meet the requirements of any module and any tooth surface (with or without chamfering, non-standard rack, etc.). The automatic grinding of the rack grinding wheel greatly reduces the user's cost and operation Difficulty.
 
(3) The worktable is wide enough to process multiple racks at a time, which also requires the machine tool to have sufficient rigidity.
 
2. On-machine testing technology
 
Through the on-machine inspection, the inspection report can be quickly output, and the compensation processing can be performed according to the inspection result, which greatly shortens the process of processing-three-coordinate detection-adjustment of the machine-reprocessing.
 
3. Intelligent process software
 
The machine tool operator is concerned about the ease of use of the machine tool. The gear grinding machine must have an intuitive and easy-to-operate human-machine interface, an intelligent error-proof mechanism and an intelligent process operation process.
 
4. Dynamic balancing technology
 
Dynamic balancing is a common technology for all grinding machine tools. If the dynamic balance of the grinding wheel spindle is not good, it will directly affect the grinding accuracy of the workpiece, which will cause large vibration of the machine tool and poor grinding accuracy.
 
5. AE technology
 
AE technology is actually an application of acoustic emission sensors. Through AE technology, it can realize automatic alignment of workpieces, automatic processing allowance detection and processing allowance allocation. In addition, AE is also an important technical means to prevent collisions.
 
How to maintain the band saw blade grinding machine?
 
(1) The sliding guide rail of the bed should be well lubricated, and yellow grease can be applied around the end of the slider. The middle section of the left and right sliders is lubricated with an oil cup, and lubricating oil is added to the oil cup every 24 hours of operation.
 
(2) The surface of the roller should be kept well lubricated, and grease should be added to the oil hole of the roller every 24 hours.
 
(3) The oil in the oil tank should be kept clean. The oil should be changed every 500 hours or so after the first operation, and thereafter every 300 hours.
 
(4) The primary oil filter should be removed and cleaned every six months (be careful not to damage it).
 
(5) Cleaning The keyboard, driver and display of the computer, as well as amplifiers, integrated circuits and sensors should be kept clean, and should be cleaned at the end of each shift.
 
(6) Check the fasteners at all parts to make them in a tightened state.
 
(7) If it is found that the forward and retreat failures, first check whether the solenoid valve is operating as if the solenoid valve is operating normally, and then check the sequence valve 6X3, overflow valve YF-L20H4 or one-way unloading valve 4HD3 for impurities stuck. If you find that the gear grinding machine is stuck, disassemble it and clean it with gasoline or diesel oil, then reinstall it.
 
Keyword:

CONTACT US

Tel:0086 757-82800952     Fax:0086 757-82800953 
QQ Email:1150353041@qq.com
Email:ldx@gdlidexin.com
Contact:Mr. Tu(0086 13823458229) Miss Lei(0086 13690538372
Add:No. 3, South District, Luanhe Industrial Zone, Luocun, Nanhai District, Foshan City

FOLLOW US

Foshan Li Dexin Machinery Manufacturing Co., Ltd.

Mobile website

Alibaba Mall

Foshan Li Dexin Machinery Manufacturing Co., Ltd.

WeChat

COPYRIGHT ©2020 Foshan LDX Machinery Manufacturing Co., Ltd. All Rights Reserved