Welcome to LDX official website!
Foshan Li Dexin Machinery Manufacturing Co., Ltd.
Specializing in the production of TCT circular saw blades, TCT band saw blades, finger joint knives, flying knives, various non-standard CNC grinding machine production lines
Check category
How much do you know about the operating specifications of the fully automatic saw blade grinding machine?
- Time of issue:2019-05-28 19:35
(Summary description)How much do you know about the operating specifications of the fully automatic saw blade grinding machine?
How much do you know about the operating specifications of the fully automatic saw blade grinding machine?
(Summary description)How much do you know about the operating specifications of the fully automatic saw blade grinding machine?
- Time of issue:2019-05-28 19:35
How much do you know about the operating specifications of the fully automatic saw blade grinding machine?
1. When the equipment is stopped for more than eight hours, the machine should be hydraulically lubricated for 5-10 minutes, then manually run each moving shaft to check whether the operation of each part is normal; confirm that the operation is normal, the lubrication is good, and there is no alarm. start working.
2. It is forbidden to open the electric control cabinet without permission.
3. The operator must be familiar with the structural performance of the device, the transmission principle and the processing application. After obtaining the operation certificate, the operator can operate independently.
4, the operator must conscientiously do "three good" (management, use, repair) "four sessions" (will use, will maintain, will check, will eliminate the fault).
5. The operator must abide by the “five disciplines” of using the equipment and the “four requirements” of the maintenance equipment.
6. The operator should check the equipment at any time according to the requirements of “Rolling Inspection Contents”.
7, in strict accordance with the equipment oil requirements for refueling, to achieve lubrication "five fixed" (timed, fixed point, quantitative, qualitative, fixed).
8. It is forbidden to carry out trial operation and prohibit shifting during processing.
9. During the work, the sound is prevented from being mixed into the drip system to prevent the waste such as cotton yarn from falling into the machine.
10. It is strictly forbidden to move or damage the warning signs on the machine.
What is the key technology of the fully automatic saw blade grinding machine rack?
1, technology
1) Due to the particularity of the rack, the grinding wheel is generally wider, and multiple slots are ground at one time. At this time, the grinding load is large, the rigidity of the machine tool needs to be good enough, and the spindle power is large enough.
3) Adopting a single piece of small rounded diamond roller, it can satisfy any modulus, any tooth surface requirement (with or without chamfering, non-standard rack, etc.) automatic dressing of the rack grinding wheel, which greatly reduces the user's use cost and operation difficulty. .
2) The work surface is wide enough to handle multiple racks in one setup, which also requires the machine to have sufficient rigidity.
2, on-machine detection technology
Through the on-machine detection, the test report can be quickly output, and the compensation process can be performed according to the test result, which greatly shortens the process of processing - three-coordinate detection - adjusting the machine tool - re-machining.
3, intelligent process software
Machine tool operator Zui pays attention to the ease of use of the machine tool. The gear grinding machine must have an intuitive and easy-to-operate man-machine interface, intelligent error-proof mechanism and intelligent process operation.
4, dynamic balance technology
Dynamic balance is a common technology for all grinding machine tools. The dynamic balance of the grinding wheel spindle is not good, which will directly affect the grinding accuracy of the workpiece, which will cause the machining vibration of the machine to be large and the grinding precision to be poor.
5, AE technology
AE technology is actually an application of acoustic emission sensor. Through AE technology, automatic centering of workpieces, automatic allowance detection and machining allowance distribution can be realized. In addition, AE is also an important technical means to prevent collision.
Keyword:
CONTACT US
Tel：0086 757-82800952 Fax：0086 757-82800953
QQ Email：1150353041@qq.com
Email：ldx@gdlidexin.com
Contact：Mr. Tu（0086 13823458229） Miss Lei（0086 13690538372）
Add：No. 3, South District, Luanhe Industrial Zone, Luocun, Nanhai District, Foshan City
FOLLOW US
Mobile website
Alibaba Mall
COPYRIGHT ©2020 Foshan LDX Machinery Manufacturing Co., Ltd. All Rights Reserved
Powered by: 300.cn